Microscan MS-4Xi Manuel d'utilisateur Page 100
- Page / 360
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5-18
MS-4Xi Imager User Manual
Capture Mode
Number of Captures
Note: The range of maximum number of captures is dynamic. This range is dependent
on the maximum image size in the system. A full-size image (1280 x 1024) reduces the
maximum number of images to 6. The smaller the image size, the greater the maximum
number of captures. Once the image size is reduced to small enough dimensions, the
maximum number of captures will be capped at 64.
If a user enters a maximum capture value greater than that allowed, the value will be
limited to the number of system images. This command also affects the number of
stored images allowed in the system. If the maximum number of captures is selected,
the number of stored images allowed will be 0.
Rapid Capture Mode
Usage:
Number of Captures
is used to specify the number of captures to be processed
in Rapid Capture Mode.
Definition:
Sets the total number of captures that are processed during a read cycle in
Rapid Capture Mode
. This feature is used in conjunction with
Capture Timing
parameters to specify the capture sequence of a rapid capture read cycle.
Serial Cmd:
<
K241,
capture mode,
number of captures
,rapid capture mode>
Default: 1
Options:
1
to 64
Definition: In Rapid Capture Mode, one or multiple captures (as many as 32) can be
taken at an interval specified by the time-between-captures parameter. In
this mode, the only limiting time factor is integration and transfer timing.
Serial Cmd:
<
K241,
capture mode,number of captures,
rapid capture mode
>
Default: Timed Capture
Options:
0 = Timed Capture
1 = Triggered Capture
- MS-4Xi Imager 1
- User Manual 1
- Disclaimer 2
- Latest Manual Version 2
- Technical Support 2
- Warranty 2
- Table of Contents 3
- Chapter 5 Read Cycle 4
- Chapter 6 Symbologies 4
- Chapter 7 I/O Parameters 4
- Introduction 5
- Chapter 8 Symbol Quality 5
- Chapter 9 Matchcode 5
- Chapter 14 Output Format 7
- About the MS-4Xi Imager 8
- MS-4Xi Communications 8
- Warning and Caution Summary 9
- MS-4Xi Imager User Manual 10
- Statement of RoHS Compliance 11
- 1 Quick Start 13
- Step 1 — Check Hardware 14
- Step 2 — Connect the System 15
- Step 4 — Install ESP 17
- Step 5 — Select Model 18
- Step 6 — Connect 19
- Locate by ESP 20
- Locate by EZ Button 21
- Step 8 — Calibrate 22
- Step 9 — Test Read Rate 23
- Saving Options 25
- Save Configuration in ESP 26
- 2 Using ESP 27
- Calibrate 28
- Application Mode 29
- Menu Toolbar 30
- Preferences > General Tab 32
- Preferences > Terminal Tab 33
- Sizing Information 34
- Preferences > Advanced Tab 35
- Connect to Readers via TCP/IP 36
- Use Default Storage Location 36
- Document Memo 37
- Model Memo 37
- Connection Wizard 38
- Bar Code Dialog 39
- Navigating in ESP 40
- Send/Receive Options 41
- Defaulting 42
- Advanced Options 42
- Using EZ Trax 43
- 3 Communications 45
- Communications by ESP 46
- Host Port Connections 48
- Host Port Protocol 49
- ACK/NAK Options 50
- Polling Mode Options 51
- Ethernet 52
- Communications 53
- IP Address Mode 54
- TCP Port 1 55
- TCP Port 2 56
- Search and Configure Mode 57
- Response Timeout 58
- LRC Status 59
- Point-to-Point (Main Port) 60
- Polling Mode (Main Port) 60
- ACK/NAK (Main Port) 60
- Preamble 62
- Postamble 63
- 4 Calibration 65
- Calibration Serial Commands 66
- Calibration Overview 66
- Calibration Options 67
- Disabled (Shutter Speed) 68
- Enabled (Shutter Speed) 68
- Fast Shutter 68
- Symbol Type 69
- Disabled 71
- Row and Column 71
- Straight Line 72
- Straight Line Framed 72
- Line Scan Height 73
- Processing 73
- Calibration by ESP 74
- After Calibration 75
- Initiating Calibration 76
- Read Rate LEDs 77
- Beeper/Green Flash 77
- Terminal 78
- Focus Pass 79
- Medium Pass 80
- Fine-Tune Pass 81
- 5 Read Cycle 83
- Read Cycle by ESP 84
- Read Cycle Serial Commands 85
- Read Cycle Setup 86
- Multisymbol 87
- Trigger Mode 88
- Continuous Read 1 Output 89
- External Level 90
- External Edge 90
- Serial Data 91
- Serial Data and Edge 91
- Leading Edge Trigger Filter 92
- Trailing Edge Trigger Filter 92
- External Trigger Polarity 93
- Serial Trigger 94
- , : <K229h,2C> 95
- , : <K230h,2C> 96
- End of Read Cycle 97
- New Trigger 98
- Timeout or New Trigger 98
- Last Frame 98
- Last Frame or New Trigger 98
- Read Cycle Timeout 98
- Capture Mode 99
- Number of Captures 100
- Rapid Capture Mode 100
- Timed Capture 101
- Triggered Capture 102
- Capture Timing 103
- Time Between Captures 104
- Image Processing Timeout 105
- Image Storage 106
- Image Storage Example 107
- Minimum Good Reads 108
- 6 Symbologies 111
- Symbologies by ESP 112
- Symbologies Serial Commands 113
- Data Matrix 114
- Aztec Code 116
- Micro QR Code 118
- Fixed Symbol Length (Code 39) 120
- Full ASCII Set (Code 39) 121
- Code 128 122
- EAN 128 Status (Code 128) 123
- Output Format (Code 128) 123
- (Code 128) 123
- Fixed Symbol Length (BC412) 125
- Interleaved 2 of 5 126
- Symbol Length (Code 93) 129
- Start/Stop Match (Codabar) 130
- Start/Stop Output (Codabar) 130
- Symbol Length (Codabar) 131
- EAN Status 133
- Separator Status (UPC/EAN) 134
- Separator Character (UPC/EAN) 135
- Supplemental Type (UPC/EAN) 136
- Pharmacode 137
- Bar Width Status (Pharmacode) 138
- Direction (Pharmacode) 138
- Postal Symbologies 139
- Postal Symbology Type 140
- POSTNET Status 142
- PLANET Status 142
- USPS4CB Status 143
- POSTNET Allow B and B’ Fields 143
- Australia Post Allow 0 FCC 143
- GS1 DataBar 144
- DataBar Limited 145
- DataBar-14 145
- Fixed Symbol Length (PDF417) 146
- MicroPDF417 147
- Composite 148
- Narrow Margins 149
- Symbology Identifier 150
- Background Color 151
- 7 I/O Parameters 153
- I/O Parameters by ESP 154
- I/O Parameters 155
- Symbol Data Output 156
- Good Read 157
- When to Output Symbol Data 158
- No Read Message 159
- Output Indicators 160
- Static Presentation Mode 161
- Mismatch 161
- Target Pattern 162
- Green Flash Duration 163
- LED Configuration 165
- Serial Verification 166
- Control/Hex Output 167
- EZ Button 168
- Default on Power-On 169
- Load Configuration Database 169
- Save for Power-On 169
- EZ Button Modes 170
- Target System 171
- Bar Code Configuration 171
- EZ Button Operation 171
- Configurable Output 1 172
- Trend Analysis 173
- Symbol Quality 173
- Diagnostic Warning 173
- In Read Cycle 173
- Output State 174
- Pulse Width 174
- Output Mode 174
- Trend Analysis Output 1 175
- Trend Analysis Mode 176
- Trigger Evaluation Period 177
- Number to Output On 177
- Decodes per Trigger Threshold 177
- Output on Symbol Contrast 178
- Output on Print Growth 178
- Symbol Contrast Threshold 179
- Print Growth Threshold 180
- Diagnostics Output 1 181
- Configurable Output 2 182
- Trend Analysis Output 2 182
- Diagnostics Output 2 182
- Configurable Output 3 183
- Trend Analysis Output 3 183
- Diagnostics Output 3 183
- Power On/Reset Counts 184
- Time Since Reset 185
- Service Message 186
- Frame Information 187
- Image Output 188
- Communication Port 189
- File Format 189
- JPEG Quality 189
- Image Output Example 190
- Database Identifier Output 191
- Quality Output 192
- Configuring EZ Trax Output 193
- EZ Trax Output 194
- Comm Port 194
- Image Mode 194
- Image Format 194
- Object Info Output 195
- Grade Output 195
- 8 Symbol Quality 199
- Symbol Quality by ESP 200
- Overview of Symbol Quality 202
- Report Tab 203
- Locate Tab 204
- Preferences Tab 205
- Symbol Quality Separator 206
- Data Matrix Output Mode 207
- Symbol Contrast 208
- Print Growth 208
- (Data Matrix Only) 209
- Total Read Time 211
- Capture Time 211
- Locate Time 211
- Decode Time 212
- Matrix Size 212
- (Data Matrix Only) 212
- Quiet Zone (Data Matrix Only) 213
- 9 Matchcode 215
- Matchcode by ESP 216
- Matchcode Serial Commands 217
- Overview of Matchcode 218
- Matchcode Type 219
- Sequential Matching 220
- Match Start Position 220
- Match Length 220
- Wild Card Character 221
- Sequence on No Read 222
- Sequence on Mismatch 223
- Match Replace 224
- Mismatch Replace 225
- New Master Pin 226
- Camera and IP Setup 227
- Camera and IP Setup by ESP 228
- Evaluation 231
- Histogram 232
- Line Scan 233
- Calibration 234
- Window of Interest 235
- Window of Interest by ESP 236
- Top (Row Pointer) 237
- Left (Column Pointer) 237
- Height (Row Depth) 237
- Width (Column Width) 237
- Configuration Database 238
- Dynamic Setup 239
- X-Mode™ 240
- Pixel Sub-Sampling 241
- AEC/AGC Mode 242
- AEC/AGC Brightness 242
- Camera Settings 243
- Shutter Speed 244
- Focal Distance 245
- Number of Focal Distances 246
- Mirrored Image 247
- Illumination Brightness 248
- Skew Correction 249
- Line Speed 250
- Symbol Direction 251
- Morphological Pre-Processing 252
- Morphological Operation 253
- Operator Size 255
- Configuration 257
- Database 257
- Number of Active Indexes 259
- Configuration Database Status 260
- Row Pointer 261
- Column Pointer 261
- Row Depth 261
- Column Width 261
- Threshold Mode 262
- Fixed Threshold Value 262
- Processing Mode 262
- Symbology 263
- Micro QR Code (Add 65536) 265
- Aztec Code (Add 131072) 265
- Database Mode 266
- Image Process Looping 267
- Image Dimensions 268
- Region of Interest (ROI) 269
- Notes on Symbol Type 272
- Terminal 275
- Terminal Window 276
- Editing a Macro 279
- Terminal Window Menus 280
- Utilities 281
- Serial Utility Commands 282
- Utilities 283
- Read Rate 284
- Enter Decodes/Second Test 285
- Enter Percent Test 285
- End Read Rate Test 285
- Counters 286
- Counters by Serial Command 287
- Device Control 288
- Differences from Default 289
- Master Database 290
- Master Symbol Database Size 291
- Enter Master Symbol Data 292
- Request Master Symbol Data 293
- Request New Master Status 294
- Delete Master Symbol Data 295
- Firmware 296
- Firmware Verification 297
- Request Checksum by ESP 298
- Default/Reset/Save 299
- Customer Default Parameters 300
- Microscan Default Parameters 300
- Imager Status Requests 301
- Learn Operations 303
- Image Library Request 304
- Bar Code Configuration Mode 305
- Output Format 307
- Output Format Serial Commands 308
- Output Format Status 309
- Format Assign 310
- Format Extract 311
- Format Extract by ESP 312
- Format Insert 313
- Format Insert by ESP 314
- Output Filter Configuration 315
- Filter Number 316
- Length 317
- Wildcard 317
- Placeholder 317
- Database Index 318
- Output Format 319
- Number of Filters 320
- Appendices 321
- General Specifications 322
- MS-4Xi Dimensions 322
- FIS Options 325
- Accessories 325
- MS-4Xi Connectors 326
- QX-1 Connectors 327
- Optoisolated Outputs 328
- PNP Output for Host Input 329
- PNP Output for External Load 330
- Optoisolated Inputs 331
- Electrical Specifications 332
- Output Wiring 333
- Serial Configuration Commands 334
- Serial Command Format 338
- Serial Command Status Request 339
- Communications Protocol 340
- ACK/NAK Data Flow Examples 341
- Error Condition 342
- Transfer 1 343
- Transfer 2 343
- Error Condition 1 345
- Error Condition 2 346
- Error Condition 3 348
- Appendix E — ASCII Table 349
- Appendix F — Operational Tips 350
- 5 Volt Devices 351
- 10-28 Volt Devices 351
- Y-Modem Method 352
- Upload Image 353
- Bit Stream Method 354
Produits connexes et manuels pour Lecteurs de codes-barres Microscan MS-4Xi
(2 pages)
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.408 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels