Microscan MS-2 Manuel d'utilisateur Page 80
- Page / 125
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5-18 MS-2 CCD Reader User’s Manual
UPC/EAN
EAN-13 Status (UPC/EAN)
Supplementals Required (UPC/EAN)
Supplemental 2 Status (UPC/EAN)
Supplemental 5 Status (UPC/EAN)
Definition: This field is enabled by default and will decode all EAN-13 symbols.
Serial Cmd:
<
K489,
UPC-A status,UPC-E status,EAN-8 status,
EAN-13 status
,supplementals
required,supplemental 2 status,supplemental 5 status,UPC-A as EAN-13,
UPC-E as UPC-A,EAN-8 as EAN-13>
Default: Enabled
Options: 0 = Disabled 1 = Enabled
Definition: A supplemental is a 2 or 5-character symbol appended to the main symbol.
When enabled, the reader decodes supplemental symbol data that has
been appended to the standard UPC or EAN symbol.
Serial Cmd:
<
K489,
UPC-A status,UPC-E status,EAN-8 status,EAN-13 status,
supplementals
required,supplemental 2 status,supplemental 5 status,UPC-A as EAN-13,
UPC-E as UPC-A,EAN-8 as EAN-13>
Default: Disabled
Options: 0 = Disabled 1 = Enabled
Definition: A 2-character symbol appended to the main symbol.
Serial Cmd:
<
K489,
UPC-A status,UPC-E status,EAN-8 status,EAN-13 status,supplementals
required,supplemental 2 status,supplemental 5 status,UPC-A as EAN-13,
UPC-E as UPC-A,EAN-8 as EAN-13>
Default: Disabled
Options: 0 = Disabled 1 = Enabled
Definition: A 5-character symbol appended to the main symbol.
Serial Cmd:
<
K489,
UPC-A status,UPC-E status,EAN-8 status,EAN-13 status,supplementals
required,supplemental 2 status,supplemental 5 status,UPC-A as EAN-13,
UPC-E as UPC-A,EAN-8 as EAN-13>
Default: Disabled
Options: 0 = Disabled 1 = Enabled
- MS-2 CCD Reader 1
- User’s Manual 1
- Disclaimer 2
- Latest Manual Version 2
- Technical Support 2
- What Is Covered? 3
- What Is Excluded? 3
- Limitation of Liability 3
- Table of Contents 4
- About the MS-2 CCD Reader 6
- About This Manual 6
- Highlighting 6
- Host Communications 6
- Warning and Caution Summary 7
- Statement of RoHS Compliance 9
- MS-2 CCD Reader User’s Manual 10
- 1 Quick Start 11
- Step 1 — Check Hardware 12
- Step 2 — Connect the System 13
- Step 3 — Install ESP 14
- Step 4 — Select Model 15
- Step 5 — Autoconnect 16
- Step 6 — Position the Reader 17
- Step 7 — Configure the Reader 18
- Saving Options 19
- Save Configuration in ESP 20
- 2 Using ESP 21
- Application Mode 23
- Menu Toolbar 24
- Preferences > General Tab 26
- Preferences > Terminal Tab 27
- Sizing Information 28
- Preferences > Advanced Tab 29
- (cont.) 30
- Connect to Readers via TCP/IP 30
- Use Default Storage Location 30
- Document Memo 31
- Model Memo 31
- Autoconnect 32
- Autoconnect (cont.) 33
- Navigating in ESP 35
- Send/Receive Options 36
- Defaulting 37
- Advanced Options 37
- 3 Communications 39
- Communications by ESP 40
- Host Port Connections 42
- Host Port Protocol 43
- Preamble 44
- Postamble 45
- 4 Read Cycle 47
- Read Cycle by ESP 48
- Read Cycle Serial Commands 49
- MS-2 Read Cycle Overview 50
- Number of Symbols 51
- Trigger Mode 53
- External Edge 54
- Serial Data 54
- Serial Data and Edge 54
- No Decode Timeout 59
- Decodes Before Output 60
- No Read Message 61
- Reader Setup 62
- 5 Symbologies 63
- Symbologies by ESP 64
- Symbologies Serial Commands 65
- Full ASCII Set (Code 39) 67
- Symbol Length (Codabar) 69
- Interleaved 2 of 5 70
- Minimum Length 71
- Fixed Length 71
- Code 128/EAN 128 72
- GS1 DataBar (RSS) 74
- MSI Code 75
- Plessey Code 76
- Industrial 2 of 5 77
- UPC-A Status (UPC/EAN) 79
- UPC-E Status (UPC/EAN) 79
- EAN-8 Status (UPC/EAN) 79
- EAN-13 Status (UPC/EAN) 80
- UPC-A as EAN-13 (UPC/EAN) 81
- UPC-E as UPC-A (UPC/EAN) 81
- EAN-8 as EAN-13 (UPC/EAN) 81
- Symbology Identifier 82
- Terminal 83
- Terminal Window 84
- Editing a Macro 87
- Terminal Window Menus 88
- Utilities 89
- Serial Utility Commands 90
- Differences from Default 91
- Firmware 92
- Firmware Verification 94
- Device Control 95
- Default/Reset/Save 96
- Reader Status Request 97
- General Specifications 100
- MS-2 CCD Reader Dimensions 100
- Appendices 101
- Serial Configuration Commands 104
- Serial Command Format 105
- Appendix E — ASCII Table 108
- Appendix F — Operational Tips 109
- 5 Volt Devices 110
- 10-28 Volt Devices 110
- Hyperlink Index 115
- Variable Length 124
- Very Large-Scale Integration 124
- Warranty 124
- Recipient Response 125
Produits connexes et manuels pour Lecteurs de codes-barres Microscan MS-2
(431 pages)
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.175 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels